Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
The article in the next paragraphs involving A Step-by-Step Guide to Installing a Bathtub is fairly remarkable. Check it out for yourself and see what you think of it.
Installing a bath tub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a moderately difficult job. If the old tub is easily obtainable, the task can move quickly; if you need to open a wall surface to get rid of the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will require an assistant to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the work and are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This post will certainly help you install a new bathtub in your washroom if you have already purchased a brand-new bathtub as well as do not require to change the setup of your previous water pipelines.
Your devices as well as material list must comprise the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted access that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will originate from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Using the two wood boards under its feet, put the bath tub in the required placement. The wood boards are handy in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the bath tub up until the spirit level checks out degree.
To install faucets, fit all-time low of the furthest flexible tap adapter to the suitable supply pipeline by making a compression join; then do the exact same for the other tap.
Switch on the water supply and examine all joints and also new pipework for leaks and tighten them if essential. Fill up the bathtub as well as likewise inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the tub should wait up until the bath tub has been made use of at least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the faucet as well as the sink. Protect the tap in place with the maker supplied backnut. Once the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the faucet finishes first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealant can fracture fairly early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently readily available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that post about Tools You Need to Install a New Bathtub when doing a search on the web. So long as you appreciated our blog post please make sure you remember to pass it around. I thank you for reading our article about How to Install a Bathtub Yourself.
24/7 ready, dial! Report this page